CL9
Repair parts for the Challenger 9,000lb, two-post, surface mounted CL9 lift. If you do not see a link to the part you need below, please contact us for further assistance.
Click on the diagrams below to see their full-sized versions.
| Diagram Item # | Part Description | Part # |
| 1a. | Power Column Weld | A1010-P |
| 1b. | Idler Column Weld | A1010-I |
| 2a. | Column Extension Weld - CL9 | A1055-0 |
| 2b. | Column Extension Weld - CL9-1 | A1055-1 |
| 2c. | Column Extension Weld - CL9-2 | A1055-2 |
| 3a. | Overhead Channel (Mid Section) | A1060 |
| 3b. | Overhead Channel (End Section) | A1061 |
| 4 | Shutoff Bar | 36074 |
| 5 | Pad | 31129 |
| 6 | Overhead Limit Switch | 12045 |
| 7 | 3/8 Dia x 1-7/8 Long Clevis Pin (Shutoff Bar) | A1064 |
| 8 | Hairpin Cotter Pin | 40124 |
| 9 | 3/8" Flat Washer | 31036 |
| 10 | 3/8-16NC x 3/4" Long Hex Flange Head Cap Screw | A1153 |
| 11 | 3/8-16NC Hex Flange Nut | A1154 |
| 12 | 3/8-16 x 3" Long NC Hex Flange Head Cap Screw | A2159 |
| Diagram Item # | Part Description | Part # |
| 20a. | Lock Release Cable Assembly - CL9 | A1135-0 |
| 20b. | Lock Release Cable Assembly - CL9-1 | A1135-1 |
| 20c. | Lock Release Cable Assembly - CL9-2 | A1135-2 |
| 21 | Lock Pawl | A1140 |
| 22 | Lock Cover | A1133 |
| 23 | Lock Pin 5/8 x 1-1/2" Long Shoulder Bolt | 30020 |
| 24 | Lock Pin Retainer (1/2-13NC Hex Lock Nut) | 37013 |
| 25 | Clevis Pin Kit | 37119 |
| 26 | Lock Spring (3/8" O.D.) | A1131 |
| 27 | Cable Spring (1/2" O.D.) - Idler Side ONLY | A1132 |
| 28 | Lock Release Clevis Assembly - Power Side ONLY | A1141 |
| 29 | Ball Handle - Power Side ONLY | 36096 |
| Diagram Item # | Part Description | Part # |
| 35a. | Power Unit, Single Phase, 60Hz, 208-230V | A1201-15 |
| 35b. | Pwer Unit, Three Phase, 60Hz, 208-230/460V | A1203-15 |
| 36 | Hyd. Elbow, 9/16 O-Ring Male to 6# Male Flare | 16167 |
| 37 | Hyd. Hose Assembly, Power Unit (22" Long) | A1123-PU |
| 38 | Bulkhead Tee, #6 Male 37 Degree Flare | A1120 |
| 39a. | Column Extension Hose, CL9-1 (24" Long) | 39101-024 |
| 39b. | Column Extension Hose, CL9-2 (48" Long) | 39101-048 |
| 40 | Hyd. Hose Assembly, Idler Column (326" Long) | A1123-I |
| 41 | Hose Clamp | A1122-12 |
| 42 | Cylinder (68" Stroke x 2" Bore) | 16138 |
| 43 | Straight Adapter, 9/16 Male O-Ring to #6 Male Flare | A1121 |
| 44 | Hyd. Hose Assembly, Power Column (81" Long) | A1123-P |
| Diagram Item # | Part Description | Part # |
| 50a. | Synchronizer Cable - CL9-0 (32'-8") CABLE PACK #A1003-0 | A1115-0 |
| 50b. | Synchronizer Cable - CL9-1 (34'-8") CABLE PACK #A1003-1 | A1115-1 |
| 50c. | Synchronizer Cable - CL9-2 (36'-8") CABLE PACK #A1003-2 | A1115-2 |
| 51 | 1/2-20NF Hex Nut | A1116 |
| 52 | 1/2-20NF Hex Jam Nut | A1117 |
| 53 | Sheave Assembly (3-1/2" Dia. x 1/4" Inner Groove) | A1041 |
| 54 | Sheave Pin | A1062 |
| 55 | Short Sheave Spacer | A1063-S |
| 56 | Long Sheave Spacer | A1063-L |
| 57 | 1" I.D. Spacer Washer | 36013 |
| 58 |
1" Ext. Retaining Ring |
36014 |
| 59 | CL9 Lower Cable Trap | A1158 |
| Diagram Item # | Part Description | Part # |
| 70 | Carriage Weld | A1025 |
| 71 | Slide Block | A1040 |
| 72 | Arm Pin Weld | A1078 |
| 73 | Inner gear | A1070 |
| 74 | 3/8-16NC x 1" Long Hex Flange Lock Head Cap Screw, Grade 5 | 12568 |
| 75 | Pull Ring | A1075 |
| 76 | Shaft | A1073C |
| 77 | Compression Spring | 31109 |
| 78 | Outer Gear | A1072 |
| 79 | 1" Ext. Retaining Ring | 36014 |
| 80a. | Front Female Arm Weld (Power Side) | B2210-P |
| 80b. | Front Female Arm Weld (Idler Side) | B2210-I |
| 81 | Fronter Intermediate Arm Weld | B17252R |
| 82 | Front Male Arm Weld | B2218 |
| 83 | Rear Female Arm Weld | B2220 |
| 84 | Rear Intermediate Arm Weld | B2230 |
| 85 | Rear Male Arm Weld | B2235 |
| 86 | M10 Stop Screw | B17258 |
| 87 | Foot Pad Assembly | B2260 |
| 88 | Rubber Insert | B2208 |
| 89 | Foot Pad Weld | B2205 |
| 90 | 2 x 30mm Round Wire Retaining Ring | B17256 |
| 91 | Threaded Sleeve | B17254 |
| 92 | 3 x 45mm Round Wire Retaining Ring | B17257 |
| 93 | Threaded Insert | B17276-1 |
| 94 | Roll Pin, 6mm Dia. x 30mm Long | B2211 |
| 95 | 10mm Flat Washer, 1mm Thick | CS1020-01-09 |
| Arm Pack, CL10 3-Stage | B2202 | |
| Front Arm Assembly (Power Side) | B2203U-P | |
| Front Arm Assembly (Idler Side) | B2203U-I | |
| Rear Arm Assembly | B2204U | |
| Arm Restraint Shaft Assembly (#'s 75,76,77,78,79) | A1077 |
| Diagram Item # | Part Description | Part # |
| 110 | Rear Female Arm Weld | A1091 |
| 111 | Male Arm Weld (Rear), Square Foot Pad Models | A1094-R |
| 112 | Optional Male Arm Weld (Rear). Round Stack Pad Models | B1094U-R |
| 113 | Foot Pad Rubber Insert (Square Foot Pad Models) | A1104 or A1104-H |
| 114 | Foot Pad Assembly (#'s 112, 113, 114, 115) | A1100 |
| 115 | Foot Pad Retainer Ring | 39111 |
| 116a. | Front Female Arm Weld (Power) | A1086-P |
| 116b. | Front Female Arm Weld (Idler) | A1086-I |
| 117a. | Male Arm Weld (Front), Square Foot Pad Models | A1094-F |
| 117b. | Optional Male Arm Weld (Front), Round Stack Pad Models | B1094U-F |
| 118 | 3/8 Male Arm Retainer Screw | 31305 |
| 119 | 3/8 Lock Washer | 31037 |
| Rear Arm Assembly (#'s 110, 111, 118, 119) | A1090 | |
| Power Side Front Arm Assembly (#'s 116, 117, 118, 119) | A1085-P | |
| Idler Side Front Arm Assembly (#'s 116, 117, 118, 119) | A1085-I |